Makita EA3201S Spezifikationen PDF herunterladen (Seite 9)

P 9/ 15

Note: Drain Fuel tank before disassembling Carburetor.

See Fig. 21. (1) Remove Hood.

(2) Turn Choke lever to the position of “STOP”.

(3) Remove two M4x40 Hexalobular socket head bolt on Intake manifold.

(4) Remove Air filter cover, Air filter, and Intake manifold.

(5) Remove one end of Tube 3-70 and one end of Tube 2.5-72 from Carburetor. (Fig. 22)

Note: Gasoline is left in Tube 3-70, and therefore, clean the gasoline with a cloth.

(6) Remove Carburetor from Throttle linkage.

Note: When setting Carburetor in place, hook Throttle linkage to the hole of Lever-throttle (designated by Black arrow in

Fig. 21).

Fig. 21 Fig. 22

Repair

DISASSEMBLING

[2] DISASSEMBLY/ ASSEMBLY

[2]-9. Ignition coil

5.5x16 Hexalobular

tapping screw (2 pcs.)

Choke

lever

Intermediate

flange

5.5x16 Hexalobular

tapping screw (2 pcs.)

Contact spring

3x10 Tapping

screw

Cable harness

Stop

mark

Air filter

cover

Tube 2.5-72 removed from

Carburetor

Tube 3-70

removed from

Carburetor

Air filter

Intake

manifold

Refer to Figs. 19 and 20.

(1) Insert two Isolating washers into two seated holes of Cylinder.

(2) Pretighten Ignition coil in place by tightening two M5x20

Hexalobular socket head bolts through Isolating washers.

(3) Insert 1R366 between Ignition coil and Flywheel and adjust

the clearance of 0.25 to 0.3mm as follows:

• Once unscrewing two M5x20 Hexalobular socket head bolts,

Push Ignition coil toward Flywheel carefully and check the

clearance. If the above clearance is obtained, tighten the bolts

to fastening torque 5 ± 0.5 N·m.

(4) Connect Flag terminal of Cable harness to Ignition coil.

(1) Remove Sprocket guard, Guide bar and Saw chain from

the machine.

(2) Remove “Recoil starter section”. See [2]-7.

(3) Remove Flag terminal on one of cable end from Ignition coil.

Note: The other cable end cannot be removed from Ignition coil

because they are integrated as a Cable harness.

(4) Remove two M5x20 Hexalobular socket head bolts. (Fig. 19)

Ignition coil with Cable harness is removed from Flywheel.

(Fig. 20)

Note: Do not lose two Isolating washers between Cylinder

and Ignition coil. (Fig. 20)

DISASSEMBLING

ASSEMBLING

Fig. 19

Fig. 20

Flag terminal

of cable harness

Flag terminal of Cable harness

for connecting with Ignition

Isolating washer (2 pcs.)

Cable harness

Cylinder

Ignition coil

Flywheel

M5x20

Hexalobular

socket head

bolt (2 pcs.)

M5x20

Hexalobular

socket head

bolt (2 pcs.)

0.25 to 0.3mm

[2]-10. Air filter, Carburetor, Intermediate flange

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Kommentare zu diesen Handbüchern

Keine Kommentare

Makita EA3201S Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kraftkettensägen Makita EA3201S