Makita LS1216 Bedienerhandbuch Seite 21
- Seite / 28
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
21
1
2
3
4
010357
NOTE:
• The maximum cutting capacity in height will be
reduced by the same amount as the platform
thickness.
(4) Place the platform on the tool so that it
extends equally over each side of the tool
base.
Secure the platform to the tool using four 6
mm wood screws through four holes in the
lower fences.
WARNING:
• Make sure that the platform is laying flat
against the tool base and secured firmly to the
lower fences using the four screw holes
provided. Failure to properly secure the platform
may result in movement and possible kickback
resulting in serious personal injury.
• Ensure that the tool is firmly mounted to a
stable and flat surface. Failure to properly mount
and secure the tool could cause the tool to be
unstable resulting in a loss of control and/or the
tool falling which may result in serious personal
injury.
(5) Install both of the removed upper fences on
the tool.
WARNING:
• Do not use the tool without upper fences
installed. The upper fences provide the adequate
support required to cut the workpiece.
If the workpiece is not supported properly it may
move resulting in possible loss of control, kickback
and serious personal injury.
1
2
3
4
010356
(6) Place the workpiece to be cut on the platform
secured to the tool.
(7) Secure the workpiece firmly against the
upper fences with a vise before cutting.
(8) Make a cut through the workpiece slowly
according to the operation titled "Slide (push)
cutting (cutting wide workpieces)."
WARNING:
• Ensure that the workpiece is secured with the
vise and make the cut slowly. Failure to properly
secure the workpiece and to cut slowly may cause
the workpiece to move resulting in possible
kickback and serious personal injury.
• Beware that after several cuts are performed at
various miter angles the platform may become
weakened. If the platform becomes weakened due
to the multiple kerf cuts left in the material the
platform should be replaced. If the weakened
platform is not replaced it may cause the
workpiece to move, during cutting, resulting in
possible kickback and serious personal injury.
Carrying tool
1
009483
Make sure that the tool is unplugged. Secure the blade
at 0° bevel angle and the turn base at the full right miter
angle position. Secure the slide poles so that the lower
slide pole is locked in the position of the carriage fully
pulled to operator and the upper poles are locked in the
position of the carriage fully pushed forward to the guide
fence (refer to the section titled "Slide lock adjustment ".)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin.
1. Stopper pin
1. Upper fence
2. Vertical vise
3. Workpiece
4. Platform
1. Screws (two each side)
2. Lower fence
3. Base
4. Platform
- Slide Compound Miter Saw 1
- SPECIFICATIONS 2
- Symbols 3
- WARNING: 3
- EC Declaration of Conformity 4
- SAFETY INSTRUCTIONS 4
- For safe operations: 4
- ADDITIONAL SAFETY RULES 5
- FOR TOOL 5
- Blade guard 7
- Positioning kerf board 7
- ASSEMBLY 11
- Vertical vise 14
- OPERATION 15
- (1) (2) (3) (4) 17
- Table (B) 18
- Table (C) 19
- 38 mm (1-1/2") 20
- Carrying tool 21
- MAINTENANCE 22
- ACCESSORIES 25
- 884908A220 28
Verwandte Produkte und Handbücher für Gehrungssägen Makita LS1216
Gehrungssägen Makita LS0815FL Bedienerhandbuch
(132 Seiten)
(132 Seiten)
Gehrungssägen Makita LS1017 Bedienerhandbuch
(120 Seiten)
(120 Seiten)
Gehrungssägen Makita LS1013L Bedienerhandbuch
(24 Seiten)
(24 Seiten)
Gehrungssägen Makita LS1220 Spezifikationen
(32 Seiten)
(32 Seiten)
Gehrungssägen Makita BLS713 Bedienerhandbuch
(136 Seiten)
(136 Seiten)
Gehrungssägen Makita BLS820 Spezifikationen
(36 Seiten)
(36 Seiten)
Gehrungssägen Makita LS0815FL Bedienerhandbuch
(21 Seiten)
(21 Seiten)
Gehrungssägen Makita LS1030N Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Gehrungssägen Makita LS711D Spezifikationen
(36 Seiten)
(36 Seiten)
Gehrungssägen Makita BLS820 Spezifikationen
(16 Seiten)
(16 Seiten)
Gehrungssägen Makita LH1040 Bedienerhandbuch
(112 Seiten)
(112 Seiten)
Gehrungssägen Makita BLS712SFE Bedienerhandbuch
(33 Seiten)
(33 Seiten)
Gehrungssägen Makita MLS100 Bedienerhandbuch
(76 Seiten)
(76 Seiten)
Gehrungssägen Makita LSSOODWA Bedienerhandbuch
(33 Seiten)
(33 Seiten)
Gehrungssägen Makita LS1040S Bedienerhandbuch
(88 Seiten)
(88 Seiten)
Gehrungssägen Makita LS0714FL Bedienerhandbuch
(24 Seiten)
(24 Seiten)
Gehrungssägen Makita LS1040F Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Gehrungssägen Makita LH1200FL Bedienerhandbuch
(108 Seiten)
(108 Seiten)
Gehrungssägen Makita LS1040S Spezifikationen
(16 Seiten)
(16 Seiten)
Canon IMAGERUNNER 3530 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Drukarki Canon IMAGERUNNER 3530.
Dostarczamy 1 pdf podręczników Canon IMAGERUNNER 3530 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern