Makita 9207SPB Bedienungsanleitung PDF herunterladen (Seite 5)

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and snagging

the accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades create

frequent kickback and loss of control.

Safety Warnings Specific for Polishing Operations:

a) Do not allow any loose portion of the

polishing bonnet or its attachment strings to

spin freely. Tuck away or trim any loose

attachment strings. Loose and spinning

attachment strings can entangle your fingers or

snag on the workpiece.

Additional safety warnings:

16. Do not leave the tool running. Operate the tool

only when hand-held.

17. Check that the workpiece is properly

supported.

18. If working place is extremely hot and humid,

or badly polluted by conductive dust, use a

short-circuit breaker (30 mA) to assure

operator safety.

19. Do not use the tool on any materials

containing asbestos.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool.

Switch action

Fig.1

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and

then push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Speed change

Fig.2

For sanding operations, use the high-speed setting "H"

for maximum performance.

For polishing and buffing operations, use the low-speed

setting "L" for suitable speed range.

Refer to the following table for the relationship between

the switch setting and the rotating speed.

Speed setting

min

-1

4,100

2,000

(R.P.M)

013727

CAUTION:

• Use the speed change switch only after the tool

comes to a complete stop.

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (auxiliary handle)

Fig.3

CAUTION:

• Always be sure that the side grip is installed

securely before operation.

Screw the side grip on the tool securely. The side grip

can be installed on either side of the tool, whichever is

convenient.

1 2 3 4 5 6 7 8 9 10 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

Makita 9207SPB Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schleifmaschinen Makita 9207SPB