Makita KP0800 Bedienungsanleitung PDF herunterladen (Seite 6)

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on

the tool.

Adjusting depth of cut

Fig.1

Depth of cut may be adjusted by simply turning the knob

on the front of the tool so that the pointer points the

desired depth of cut.

Switch action

Fig.2

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and returns

to the "OFF" position when released.

For tool with lock button

CAUTION:

• Switch can be locked in "ON" position for ease of

operator comfort during extended use. Apply

caution when locking tool in "ON" position and

maintain firm grasp on tool.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

For tool with lock-off button

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Foot

Fig.3

After a cutting operation, raise the back side of the tool

and a foot comes under the level of the rear base. This

prevents the tool blades to be damaged.

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing planer blades

CAUTION:

• Tighten the blade installation bolts carefully when

attaching the blades to the tool. A loose installation

bolt can be dangerous. Always check to see they

are tightened securely.

• Handle the blades very carefully. Use gloves or

rags to protect your fingers or hands when

removing or installing the blades.

• Use only the Makita wrench provided to remove or

install the blades. Failure to do so may result in

overtightening or insufficient tightening of the

installation bolts. This could cause an injury.

For tool with conventional planer blades

Fig.4

Fig.5

Fig.6

To remove the blades on the drum, unscrew the

installation bolts with the socket wrench. The drum cover

comes off together with the blades.

To install the blades, first clean out all chips or foreign

matter adhering to the drum or blades. Use blades of the

same dimensions and weight, or drum

oscillation/vibration will result, causing poor planing

action and, eventually, tool breakdown.

Place the blade on the gauge base so that the blade

edge is perfectly flush with the inside edge of the gauge

plate. Place the adjusting plate on the blade, then simply

press in the heel of the adjusting plate flush with the back

side of the gauge base and tighten two screws on the

adjusting plate. Now slip the heel of the adjusting plate

into the drum groove, then fit the drum cover on it.

Tighten all the installation bolts evenly and alternately

with the socket wrench.

Repeat the above procedures for the other blade.

For tool with mini planer blades

Fig.7

1. Remove the existing blade, if the tool has been in

use, carefully clean the drum surfaces and the

drum cover. To remove the blades on the drum,

unscrew the three installation bolts with the socket

wrench. The drum cover comes off together with

the blades.

Fig.8

2. To install the blades, loosely attach the adjusting

plate to the set plate with the pan head screws and

set the mini planer blade on the gauge base so

that the cutting edge of the blade is perfectly flush

with the inside flank of the gauge plate.

3. Set the adjusting plate/set plate on the gauge base

so that the planer blade locating lugs on the set

plate rest in the mini planer blade groove, then

press in the heel of the adjusting plate flush with

the back side of the gauge base and tighten the

pan head screws.

4. It is important that the blade sits flush with the

inside flank of the gauge plate, the planer blade

locating lugs sit in the blade groove and the heel of

the adjusting plate is flush with the back side of the

gauge base. Check this alignment carefully to

ensure uniform cutting.

1 2 3 4 5 6 7 8 9 10 11 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Makita KP0800 Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Elektrische Planer Makita KP0800