Makita LS1216 Bedienerhandbuch PDF herunterladen (Seite 18)

18

2

(1)

(2)

(1)

(2)

(2)

(1)

(2)

(1)

(1)

(2)

(3)

(4)

1

001557

Measuring

Measure the wall length and adjust workpiece on

table to cut wall contact edge to desired length.

Always make sure that cut workpiece length at the

back of the workpiece is the same as wall length.

Adjust cut length for angle of cut. Always use

several pieces for test cuts to check the saw

angles.

When cutting crown and cove moldings, set the

bevel angle and miter angle as indicated in the

table (A) and position the moldings on the top

surface of the saw base as indicated in the table

(B).

In the case of left bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type 45° type

Right 31.6°

45° type

Left 33.9°Left 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006361

Molding

position in

Fig. A

Molding edge against

guide fence

(1)

Ceiling contact edge should

be against guide fence.

Ceiling contact edge should

be against guide fence.

For

outside

corner

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

For inside

corner

Wall contact edge should be

against guide

fence.

Finished piece

(2)

(3)

(4)

Table (B)

006362

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° LEFT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will

always be on the LEFT side of the blade

after the cut has been made.

In the case of right bevel cut

Molding

position in

Fig. A

Bevel angleMiter angle

For outside

corner

For inside

corner

52/38° type 45° type

Right 31.6°

45° type

Right 33.9° Right 30°

52/38° type

Left 31.6° Left 35.3°

Right 35.3°

Right 35.3°Right 31.6°

(1)

(2)

(3)

(4)

Table (A)

006363

Molding

position in

Fig. A

Molding edge against

guide fence

(1)

For

outside

corner

For inside

corner

Finished piece

(2)

(3)

(4)

Table (B)

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

Wall contact edge should be

against guide fence.

Wall contact edge should b

e

against guide fence.

Ceiling contact edge should

be against guide fence.

006364

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° RIGHT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its WALL CONTACT EDGE against

the guide fence on the saw.

• The finished piece to be used will

always be on the RIGHT side of the

blade after the cut has been made.

Crown molding stoppers (optional accessories)

allow easier cuts of crown molding without tilting

the saw blade. Install them on the base as shown

in the figures.

1. Inside corner

2. Outside corner

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare