Makita LS1017 Bedienungsanleitung PDF herunterladen (Seite 3)

ENGLISH

Models:

LS1013, LS1016, LS1017, LS1018, LS1214, LS1216, LS1040, LS1221, LS0714

Inclusive of models followed by F, L and FL, if any.

Preparation

Note: Check contents of package for the following components. Please inform Makita service center of any part missing in

the package immediately.

• Miter saw stand assembly (1 unit)

• Hex wrench 6 (1 pc.)

• Wrench 13 (1pc.)

• Hex socket bolt M8 x 16 (4 pcs.)

• Hex socket bolt M8 x 30 (4 pcs.)

• Hex bolt M8 x 50 (4 pcs.)

• Washer 8 (4 pcs.)

• Wheel 300 (2 pcs.)

• Washer 8 (2 pcs.)

• Foot arm (1 pc.)

• Handle (1 pc.)

• Adjusting bolt (2 pcs.)

• Clamping nut M12 (2 pcs.)

Explanation of general view

Symbols

............. Read instruction manual.

............. Maximum allowable loading

CAUTION:

• Read and thoroughly understand this manual and the

instruction manual of the tool you use before

performing the following.

• Before installing a tool on this stand, always switch off

and unplug the tool.

• The stand should be bolted in a stable and level

surface using the right angle brackets provided on two

of four feet.

• Use only with Makita model indicated in the instruction

manual.

• Use only the handle to avoid pinched fingers when

raising or folding the stand.

• Before operating the tool, secure it to stand using bolts.

• Do not use the stand on uneven or unstable surface.

• Do not climb, sit or stand on the stand.

• When setting up the miter saw stand in the upright

position or folding it, be sure to securely keep pressing

the pipe of miter saw stand with your foot until it locks.

• When storing miter saw stand, never lean it against the

wall or the like lengthwise or sideways.

• Never pull the locking lever without holding the handle.

Assembling miter saw stand (Fig. 1)

Assemble parts for miter saw stand as disassembled parts

are packed in the carton box.

(1) Adjusting bolt

Place the stand assembly upright and insert adjusting

bolts (2 pcs.) from the below and secure these bolts by

tightening nuts.

To adjust, turn the adjusting bolts until it reaches floor

so that the miter saw stand can be kept stable.

(2) Wheel 300 (2 pcs.)

Insert the wheels onto the leg B of miter saw stand on

both sides and secure the wheels by tightening hex

socket bolt M8 x 16 (2 pcs.) with washer 8 (2 pcs.)

from upper side.

(3) Foot arm

Insert the foot arm onto the port of the leg B from

upper side and secure it by tightening hex socket bolt

M8 x 16 (2 pcs.) from backside.

(4) Handle

Insert the handle onto the miter saw stand from the

cover side and secure it by tightening hex socket bolt

M8 x 30 (4 pcs.) from the ratchet cover side.

Installing a miter saw on the miter saw

stand: (Fig. 2)

Place a miter saw so that the hole in the miter saw base

overlaps a hole in the label on the miter saw stand table

according to applicable models. These holes come with

nut M8 (4 pcs). Secure the miter saw stand with Hex bolt

M8 x 50 (4 pcs.)

How to use miter saw stand

Setting up: (Fig. 3)

1. Grip the handle and place your foot on the pipe of the

leg A of miter saw stand.

2. Release the locking lever with left hand while pressing

down the handle.

3. Grab the handle with both hands and pull it backwards

through your weight.

4. Raise the handle up to your desired one of height

levels 1 to 5 according to your work by aligning the

index bar with the height positions shown on the label.

1. Wheel 300

2. Foot arm

3. Handle

4. Adjusting bolt

5. Hex socket bolt M8 x 16

6. Flat washer 8

7. Leg B

8. Leg A

9. Hex socket bolt M8 x 30

10. Hex bolt M8 x 50

11. Locking lever

12. Shift lever

13. Pin 10-60

14. Stopper

15. Extension arm

16. Lever 40

17. Clamping screw M8 x 20

18. Leg pipe 28

(220 lbs.)

100Kg

MAX.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Makita LS1017 Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kreissägen Makita LS1017