Makita DCS460 Bedienerhandbuch Seite 19
- Seite / 36
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
19
B
Adjusting the carburetor (only for not EU-countries)
Carburetor adjustment is necessary for optimum engine
performance, for safer and more economical operation. The
engine should be warm, the air Þ lter clean, and the chain
properly tensioned. Have carburetor adjustment done by
an authorised MAKITA service centre.
The carburetor is factory-adjusted for the air pressure at sea
level. At other elevations or under other conditions of weather,
temperature, or humidity, or when breaking in a new engine, it may
be necessary to make slight adjustments to the carburetor.
You will need a tachometer (9, part No. 950 233 210) for
optimum adjustment.
Do not go below the speciÞ ed setting of the main nozzle
(H). Doing so may cause engine damage due to overheating
and insufÞ cient lubrication!
Use the supplied carburetor screwdriver (8) for carburetor adjus-
tment. It has a moulded-on projection that aids in adjusting.
Before undertaking the adjustment, run the engine for 3-5 mi-
nutes to warm it up, but not at high speed!
For proper adjustment, proceed as follows:
1. Basic setting (engine off)
Start engine and warm up.
2. Set idle
3. Check acceleration
4. Check top speed
5. Check idle speed
Repeat steps 2-5 until you get the right idle speed, good
acceleration and maximum permissible
1. Basic setting
Carefully turn the adjusting screws for the main nozzle (H)
and idle nozzle (L) clockwise until you feel a stop.
Turn adjusting screws (H) 1
1
/
2
and (L) 1
1
/
2
counter-clockwi-
se.
2. Set idle
Set the idle speed per the technical speciÞ cations.
Turning the adjusting screw (S) in (clockwise) increases the
idle speed. Turning it out (counter-clockwise) lowers the idle
speed. In no case should the chain move.
3. Check acceleration
When the throttle is pressed, the engine should go
smoothly from idle to high speed. If this is too slow, turn
the adjusting screw (L) in small (max. 1/8 turns) increments
counter-clockwise.
4. Check top speed
The basic setting H=1
1
/
2
and L=1
1
/
2
gives a maximum
speed of about 13,800 rpm.
For higher speed (electronically limited ), turn the adjusting
screw (H) a maximum 1/4 turn clockwise.The top speed
in the governor can be clearly heard from the ignition
misses.
Note: Since there is an electronic speed governor (limiter)
at 13,800 rpm that cuts off the ignition current, the top
speed cannot be read from the tachometer. Important:
To prevent engine damage, never go below setting
(H) 1
1
/
4
turns.
5. Check idle speed
Check the idle speed after setting the top speed (the
chain must not move).
Repeat the adjustment procedure starting at Step 2,
until the engine runs with the correct idle speed, good
acceleration, and top speed.
9
8
HS L
- Instruction Manual 1
- EU Conformity Declaration 2
- Table of contents Page 2
- Delivery inventory 3
- SAFETY PRECAUTIONS 4
- Technical data 9
- Denomination of components 9
- PUTTING INTO OPERATION 10
- Tightening the saw chain 11
- Chain brake 12
- CAUTION: 13
- Refuelling 14
- Adjustment range about 90° 15
- Starting the engine 16
- Checking the chain brake 17
- Working in winter 17
- MAINTENANCE 20
- Cleaning the guide bar 22
- Replacing the spark plug 25
- Replacing the starter spring 26
- Replacing the suction head 27
- Cleaning the cylinder area 27
- Maintenance and repair 29
- Spare parts 29
- Guarantee 29
- Trouble shooting 30
- DCS460 / DCS461 32
- DCS500 / DCS501 32
- Form: 995 705 302 (3.10 GB) 36
- MAKITA Werkzeug GmbH 36
- Postfach 70 04 20 36
- D-22004 Hamburg 36
Verwandte Produkte und Handbücher für Kraftkettensägen Makita DCS460
Kraftkettensägen Makita EA7900P Bedienerhandbuch
(32 Seiten)
(32 Seiten)
Kraftkettensägen Makita DCS4610 Bedienerhandbuch
(28 Seiten)
(28 Seiten)
Kraftkettensägen Makita DCS231T Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Kraftkettensägen Makita DCS232T Bedienerhandbuch
(104 Seiten)
(104 Seiten)
Kraftkettensägen Makita DCS 43 Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Kraftkettensägen Makita EA3201S Spezifikationen
(15 Seiten)
(15 Seiten)
Kraftkettensägen Makita DCS232T Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Kraftkettensägen Makita DCS 34 Wartungshandbuch
(66 Seiten)
(66 Seiten)
Canon IMAGERUNNER 2530 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Drukarki Canon IMAGERUNNER 2530.
Dostarczamy 1 pdf podręczników Canon IMAGERUNNER 2530 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern