Makita LS1212 Bedienungsanleitung

INSTRUCTION MANUALWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.www.makitatools.comS

10Adjusting the miter angleLoosen the grip by turning counterclockwise. Turn the turnbase while pressing down the lock lever. When you havemoved the g

11Switch actionCAUTION:• Before plugging in the tool, always check to see that theswitch trigger actuates properly and returns to the “OFF”position wh

12ASSEMBLYCAUTION:• Always be sure that the tool is switched off andunplugged before carrying out any work on the tool.Socket wrench storageThe socket

13Press the shaft lock to lock the spindle and use the socketwrench to loosen the hex bolt clockwise. Then remove thehex bolt, outer flange and blade.

14Dust bagThe use of the dust bag makes cutting operations clean anddust collection easy. To attach the dust bag, fit it onto thedust nozzle.When the

15CAUTION:• When performing left bevel cuts, flip the fence over to theleft position as shown in the figure. Otherwise, it willcontact the blade or a

16Horizontal vise (optional accessory)The horizontal vise can be installed in two positions on eitherthe left or right side of the base. When performi

17OPERATIONCAUTION:• Before use, be sure to release the handle from thelowered position by pulling the stopper pin.• Make sure the blade is not contac

182. Slide (push) cutting (cutting wide workpieces)Loosen the knob counterclockwise so that the carriagecan slide freely. Secure the workpiece with th

19CAUTION:• Always be sure that the blade will move down to beveldirection during a bevel cut. Keep hands out of path ofsaw blade.• During a bevel cut

2SPECIFICATIONSBlade diameter : ... 305 mm (12”)Hole diamet

20There are two common types of crown moldings and onetype of cove moldings; 52/38° wall angle crown molding,45° wall angle crown molding and 45° wall

21Example:In the case of cutting 52/38° type crown molding forposition (1) in Fig. A:• Tilt and secure bevel angle setting to 33.9°LEFT.• Adjust and s

22• Lay crown molding with its broad back (hidden)surface down on the turn base with its WALLCONTACT EDGE against the guide fence onthe saw.• The fini

23EN0002-1Compound Miter Saw Miter and Bevel Angle Settings00003152˚38˚CeilingWallWall to Crown Molding Angle: 52/38 degreesWall Angle (deg.)Bevel Ang

24 EN0003-1Compound Miter Saw Miter and Bevel Angle Settings00003245˚45˚CeilingWallWall to Crown Molding Angle: 45 degreesWall Angle (deg.)Bevel Angle

25Crown molding stoppers (optional accessories) alloweasier cuts of crown molding without tilting the sawblade. Install them on the base as shown in t

268. Wood facingUse of wood facing helps to assure splinter-free cuts inworkpieces. Attach a wood facing to the guide fenceusing the holes in the guid

279. Cutting repetitive lengthsWhen cutting several pieces of stock to the same length,ranging from 300 mm (11 - 3/4”) to 470 mm (18 - 1/2”),use of th

28Carry the tool by holding both sides of the tool base asshown in the figure. If you remove the holders, dust bag, etc.,you can carry the tool more e

29Make sure that the pointer points to 0° on the miterscale. If the pointer does not point to 0°, loosen thescrew which secures the pointer and adjust

3For Your Own Safety Read Instruction Manual Before Operating Tool Save it for future reference GENERAL SAFETY PRECAUTIONSUSA007-1(For All Tools)1.KNO

30Make sure that the two pointers on the arm point toeach 0° on the bevel scale on the arm holder. If theydo not point to 0°, loosen the screws which

31After use• After use, wipe off chips and dust adhering to the toolwith a cloth or the like. Keep the blade guard cleanaccording to the directions in

Memo32

33First-ClassPostageRequiredPost Office willnot deliverwithout properpostage.Makita U.S.A., Inc.14930 Northam StreetLa Mirada, CA 90638-5753FoldCut

341. This product was purchased from:Home CenterHardware/Lumber StoreTool DistributorIndustrial SupplyConstruction SupplyOther ( )

35FACTORY SERVICE CENTERS1-800-4-MAKITARETAIN THIS PORTION FOR YOUR RECORDSARIZONA3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850CALIFOR

WARNINGSome dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Calif

419.CHECK DAMAGED PARTS. Before furtheruse of the tool, a guard or other part thatis damaged should be carefully checkedto determine that it will oper

5ADDITIONAL SAFETY RULESUSB036-2DO NOT let comfort or familiarity with product (gained fromrepeated use) replace strict adherence to slide compound sa

619.Make sure the shaft lock is releasedbefore the switch is turned on.20.Be sure that the blade does not contactthe turn base in the lowest position.

7INSTALLATIONBench mountingWhen the tool is shipped, the handle is locked in the loweredposition by the stopper pin. Release the stopper pin by lower-

8If the blade guard is especially dirty and vision through theguard is impaired, use the supplied socket wrench to loosenthe hex bolt holding the cent

9Maintaining maximum cutting capacityThis tool is factory adjusted to provide the maximum cuttingcapacity for a 305 mm (12”) saw blade.When installing