Makita BLS712SFE Bedienerhandbuch

Cordless Slide Compound Saw Equipped with Electric Brake 190 mm (7-1/2”) MODEL BLS712SF I MODEL BLS712SFE 190 mm (7-1/2”) MODEL BLS712SH / MODEL BLS

If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger or battery cartridge are clog

This tool should be bolted with two bolts to a level and stable surface using the bolt holes provided in the tool’s base. This will help prevent tip

Press the shaft lock to lock the spindle and I use the socket wrench to loosen the hex bolt (left-handed) clockwise. Then remove the hex bolt, outer

Safety cover When lowering the handle, the safety cover rises automatically. The cover returns to its original position when the cut is completed and

Positioning kerf board This tool is provided with the kerf boards in the turn base. The kerf boards are factory adjusted so that the saw blade does n

Maintaining maximum cutting capacity This tool is factory adjusted to provide the max. cutting capacity for a 190 mm (7-1/2") saw blade. When usi

Positioning for adjusting the miter angle The turn base turns up to 47" to the left and 57" to the right. Loosen the grip by turning co

1. Vertical vise I The vertical vise can be installed in two positions on either the left or right side of the guide fence, or the holder assem- bly

3. Holders and holder assembly (optional accessories) The holders and the holder assembly can be installed on either side as a convenient means of sup

Switch action CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch When not using the tool, remove the l

S PE CI F I CAT1 0 N S Model BLS712 Blade diameter ... 180 mm (7-1/8") - 190 mm (7-1/2"

2. Slide (push) cutting (cutting wide workpieces) *Workpieces up to 50 mm (2") high and 182 mm (7-1/8") wide can be cut in the follow- *Loos

CAUTION: *During a bevel cutting, it may create a condition whereby the piece cut off will come to rest against the side of the blade. If the blade IS

*There are crown and cove molding joints which are made to fit "Inside" 90" corners (0 and 0) in Fig. C) and "Outside" 90&quo

Compound Miter Saw Miter and Bevel Angle Settings 71 72 73 74 Ceiling - - 3 39.9 40.8 39.6 40.3 39.3 39.8 390 39.2 Wall to Crown Molding Angle: 52

Compound Miter Saw Miter and Bevel Angle Settings Ceiling Wall to Crown Molding Angle: 45 degrees Wall 1 Bevel I Miter I 75 I 34.1 ) 42.7 I 76 I 33.9

7. Cutting repetitive lengths I When cutting several pieces of stock to the same length, ranging from 220 mm (8-5/8") to 385 mm (1 5-1/8"),

Carrying tool Make sure that the battery cartridge is removed. Secure the blade at 0" bevel angle and the turn base at 57" miter angle to th

Lower the handle fully and lock it in the lowered position by pushing in the lock pin. Square the side of the blade with the face of the guide f

Carefully square the side of the blade with the top surface of the turn base using the triangular rule, try square, etc. by turning the 0" be

Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes

USA005-1 For Your Own Safety Read Instruction Manual Before Operating Tool Save it for future reference GENERAL SAFETY PRECAUTIONS (For All Tools) 1.

ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other acc

Set plate Part No. 1224724 High Capacity Battery Charger Model DC24SA Ni-M H (Nickel Metal Hydride) battery 82417 Part No. 1931 28-2 Vise assembly (ho

32

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to

16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before inserting battery. 17. USE RECOMMENDED ACCESSORIES. Consul

US6033 1 ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Keep hands out of path of saw blade. Avoid contact with any coasting blade. It can 3. Do

uscoo2-1 Length of Cord (Feet) 25 50 100 AWG Size of Cord 18 18 18 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THES

uscoo2 1 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do

Installing or removing battery cartridge *Always switch off the tool before inser- tion or removal of the battery cartridge. *To remove the battery

Cooling system This charger is equipped with cooling fan for heated battery in order to enable the battery to prove its own performance. Sound of co