Makita ARBOR 2711 Bedienerhandbuch

Table Saw Arbor thole 255 mm (10") MODEL 2711 With Electric Brake No load Dimensions Ne, Blade Cutt,ng CaPdCmeF Table size IL x WI Sliding table

Installing and adjusting rip fence Loosen the lever on the rip fence and fit the rip fence on the ruler guides. To check to be sure that the

Tighen the lever on the rip fence. If the rip fence is not secure enough, leave the lever in the tightened position and tighen the screw in th

Installing blade guard CAUTION : Before installing the blade guard, adjust the depth of cut to its maximum elevation. (Note: The depth of cut

Positioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed

Hand tool storage pocket The table saw comes with a hand tool storage pocket in the base. Keep wrenches, screwdriver, etc. in this pocket. Adjus

Bevel cutting Loosen the lock lever clockwise, then tilt the blade by swinging the knob until it reaches the desired angle (0 to 45 degrees).

Adjusting miter angle Loosen the miter gauge installation screws and adjust the miter gauge to the desired angle (0 to 45 degrees). Then tighten

Operation CAUTION : *Make sure the blade guard works smoothly and properly for making both square cuts and bevel cuts before operation. *Never wi

Push block Use a 19 mm (3/4") piece of plywood. 120 .;.4-)fm11 mm (5") Faceledge parallel 6 mm (1/4"l 5o mm (2") (5") Handle

Crosscutting CAUTION : When making a crosscut, remove the rip fence from the table. When cutting long or large workpieces, always provide adequate s

For Your Own Safety Read Instruction Manual Before Operating Table Saw GENERAL SAFETY PRECAUTIONS (For All Tools) 1 2. 3. 4. 5. 6. 7. 8. 9. 10. 1

The wooden gauge cannot be used for miter cutting. 19 mm (3/4") * 63" (2-1 /2") 19 mm (3/4") * 55mm (2-1/8") NOTE: Miter cutt

When a spacer block can be placed between the miter gauge and workpiece, you can obtain a greater miter cutting capacity. Ripping CAUTION When r

i) When the width of rip is 150 mm (6") and wider, carefully use your right hand to feed the workpiece. Use your left hand to hold th

Feed the workpiece by hand until the end is about 25 mm (I”) from the front edge of the table. Continue to feed using the push block on the top of th

MA1 NT ENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning C

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool speci- fied in this manual. The use of an

@ Use the chart below to select the proper cutters to obtain the various cutting widths. 114" I I 5116" 7/16" 112" 0 9/16" 5

When installing two outside cutters without any inside cutter, be sure that the cutter tips do not face each other. 0 X @ While tightening th

Featherbords are used to keep the work- piece in contact with the rip fence and table as shown, and to stop kickbacks. To install feathe

Ring (Part No. 257137-6) When cutting groove 1/4", 5/16", 3/8", 7/16", 1/2", 9/16" or 5/8", use this ring or rin

17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injur

Saw blades 0 Chisel tooth combination saw blade For rip and cross-cut work. Most frequently used for general carpentry. Hole Part No. 255-7A I 255 (1

Holder set (Part No. 191773-7) Convenient to attach for better support of long workpieces. Attach the holder to the reverse side of the I I CAUTION :

Jan 22 '87 US 255 mm (IO") TABLE SAW Model 2711 32

Note. The switch and other part configurations may differ from country to country 33

MODEL 2711 $FD DESCRIPTION Jan 22 87 US sD DESCRIPTION MACHINE ~ 2 3 4 5 6 7 8 9 IO 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 31 32 3

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted

G R 0 U N D I N G INSTRUCT IONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least res

ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Don't use the tool in presence of flammable liquids or gases. 3. Never use the tool with an a

jam the blade in the workpiece, turn the tool off immediately. Unplug the tool. Then clear the jam. 18. Never remove cut-off pieces near the blade or

Movement and transport of table saw Before moving the table saw, tighten the wing bolt to secure the sliding table. When moving the table saw,

Installing miter gauge Insert the wooden gauge into the miter gauge and tighten the two screws lightly but firmly. The wooden gauge will be u

Install the blade between the two flanges. Then install the outer flange and hex nut onto the arbor, making sure the teeth of the blade