Models No. DescriptionPRODUCTCONCEPTION AND MAIN APPLICATIONS SpecificationStandard equipmentOptional accessoriesP 1/22TECHNICAL INFORMATIONLHWNo, b
RepairP 10/22[3] DISASSEMBLY/ASSEMBLYBFL301R/ BFL402R2) Remove Flat washer 8 from Spindle complete. (Flat washer 8 may remain in Angle head complete.)
RepairP 11/22[3] DISASSEMBLY/ASSEMBLYBFL301R/ BFL402RFig. 35 Fig. 36 Fig. 37flatsAdjustable wrenchNo.1R223No.1R341Fig. 34DISASSEMBLING1) Remove Light
RepairP 12/22[3] DISASSEMBLY/ASSEMBLYBFL301R/ BFL402RBFL301R/ BFL402RASSEMBLING1) Assemble Needle bearing 1212, Thin washer 12 and Spacer to Spiral
RepairP 13/22[3] DISASSEMBLY/ASSEMBLYAll ModelsFig. 41Cam DSteel ball 4(3 pcs)Steel ball 5.0(3 pcs)*Cam on Torx screw sideSteel ball 4 (3 pcs) and Ste
RepairP 14/22[3] DISASSEMBLY/ASSEMBLYAll ModelsFig. 425) Insert short leg of hex wrench 6 into the hole of Spindle, and fix long leg of the hex wrench
RepairP 15/22[3] DISASSEMBLY/ASSEMBLYAll Models[3] -9. Gear Case SectionDISASSEMBLINGASSEMBLING1) Remove Light cover, Switch lever and Compression spr
RepairP 16/22[3] DISASSEMBLY/ASSEMBLYAll Models[3] -9. Gear Case Section (cont.)ASSEMBLING4) Assemble Gear case section and Motor control unit to H
RepairP 17/22[3] DISASSEMBLY/ASSEMBLYAll ModelsAll Models[3] -10. Switch SectionDISASSEMBLING1) Remove Clutch case section and Housing (L). (BFL201
P 18/22Fig. D-1Circuit diagramStatorControllerTerminalMain switchSwitch unit B(for rotationreverse)Switch unit A(for Trigger)Switch unit C(for clutch)
P 19/22Fig. D-2Wiring diagramSwitchTerminalPower supplycircuitConnectorrib (A)[1] Wiring Around ControllerReceptacleTerminalLead wire (black)Lead wire
P 2/22Repair[1] NECESSARY REPAIRING TOOLSCAUTION: Remove the battery from the machine for safety before repair/ maintenance, in a
P 20/22Fig. D-3Wiring diagram[2] Wiring Around StatorSwitch unit (for Clutch)Lead wire holderFirst, put the following Lead wiresfrom Controller in pla
P 21/22Fig. D-4Wiring diagram[3] Wiring of Lead Wires of LED CircuitBFL201RRoute Lead wiresunder the two tabs.ribtabtabs viewed fromleft sidePut Conn
P 22/22Fig. D-5Wiring diagram[3] Wiring of Lead Wires of LED Circuit (cont.)BFL301R/ BFL402Rtabrib (J)rib (I)rib (H)Route Lead wiresbetween rib (H) a
P 3/22Repair[2] LUBRICATION and ADHESIVE APPLICATIONLUBRICATIONApply Makita grease N. No.2 to the following portions designated with the black triang
P 4/22Repair[2] LUBRICATION and ADHESIVE APPLICATIONApply the following lubricants to protect parts and product from unusual abrasion (Fig. 2): Sea
RepairP 5/221) Connect Connector of LED circuit with that of Motor control unit. and put LED circuit in place on Light holder. Then fix lead wires
RepairP 6/222) Remove Flat washer 6 from Spindle complete. (Flat washer 6 may remain in Angle head complete.) Remove Spindle complete from Bearing
RepairP 7/221) Remove Light cover by unscrewing two M4x8 Pan head screws, then remove Switch lever and Compression spring 2. (Fig. 13)2) Remove Ang
RepairP 8/22Do the reverse of the disassembling steps. (Refer to Figs. 17 to 13.)Note 1: Spacer is not reversible when assembled to Spiral bevel gear
RepairP 9/22[3] -4. LED Job Light Section[3] DISASSEMBLY/ASSEMBLYBFL301R/ BFL402R*Shown in Fig. 20 are the parts of Job light section.1) Remove Lead c
Kommentare zu diesen Handbüchern